How Do I Use My Saber?

  • To turn ON: Tap the power button once,

  • To turn OFF: Tap the power button once

  • To mute sound: While the saber is OFF- hold the power button down for three seconds. When you turn it on there will be no sound.

  • To unmute sound: While the saber is OFF- hold the power button down until you hear the saber produce a brief noise. When you turn it on there will be sound.

  • To make a double sided saber: Unscrew the bottom piece of your saber VERY carefully. When you take this piece off you are exposing the inner electronics, therefore it is pertinent that you do not disturb the wiring, otherwise you may damage your sabers ability to work properly. Once you have unscrewed the first saber, screw the coupler on to it (KEEP the circular mesh piece inside, do not remove it when you take the end off). Once the coupler has been screwed on to the first saber, you should then carefully screw the end off of the second saber and attach it to the coupler. Please be sure to screw the coupler on tightly to both ends so that it does not become loose during use. Stow the ends of your sabers in a safe place, if you lose them you will have no bottom to your saber when you uncouple the sabers! NOTE: when attaching the coupler, make sure the wires do not become twisted. If they become twisted they could disconnect.

  • Enable lock up effect: While powered on, hold down the power button for however long you please to enable the lockup effect.

  • To charge your saber: Your sabers lights will begin to dim and flicker when it needs to be charged. Plug the accompanying power cord into any USB charging device and plug the opposite end into the charging port on your saber. You will notice a faint light coming from the base of the blade while the saber is charging. For a full charge, leave your saber plugged in for 3-4 hours. *Charging times may vary depending on power source

Tier 1:

  • To power ON your saber: Tap power button once to awaken from sleep mode, and immediately hold down for three seconds.

  • To power OFF: Follow the same process for powering on; tap the power button once and then hold down for three seconds and the saber will power down.

  • To remove blade: With the hex key provided, remove the screws at the base of the blade (keep these screws in a safe place so you can put them back in when you are ready to reattach your blade). Gently pull the blade out of the hilt. Attach the red cap to prevent dust and other materials from getting inside of your blade. To reattach your blade, gently slide it back into the hilt and fasten the screws back into place. Make sure to tighten the screws efficiently; loose screws may cause damage to your saber when dueling or cause your blade to fly out when swung.

  • To make a double sided saber: Unscrew the bottom piece of your saber VERY carefully. When you take this piece off you are exposing the inner electronics, therefore it is pertinent that you do not disturb the wiring, otherwise you may damage your sabers ability to work properly. Once you have unscrewed the first saber, screw the coupler on to it (KEEP the circular mesh piece inside, do not remove it when you take the end off). Once the coupler has been screwed on to the first saber, you should then carefully screw the end off of the second saber and attach it to the coupler. Please be sure to screw the coupler on tightly to both ends so that it does not become loose during use. Stow the ends of your sabers in a safe place, if you lose them you will have no bottom to your saber when you uncouple the sabers! NOTE: when attaching the coupler, make sure the wires do not become twisted. If they become twisted they could disconnect.

  • Enable lock up effect: While the saber is on, quickly double tap the power button to activate lock up effect. To disable the lock up effect, rapidly double tap again.

  • To charge your saber: Your sabers lights will begin to dim and flicker when it needs to be charged. Plug the accompanying power cord into any USB charging device and plug the opposite end into the charging port on your saber. The power button will flash while the saber is charging. For a full charge, leave your saber plugged in for 3-4 hours. *Charging times may vary depending on power source.

  • To change sound fonts (including mute function): While saber is off, double tap power button to switch between sound fonts. The next time you power on your saber, the changes will have taken effect.

  • To mute your saber: see how to change sound fonts 

Tier 2:

Tier 3:

  • To power ON: Tap the power button once 

  • To power OFF: Tap the power button once 

  • To change colors: When the saber is turned on, quickly and firmly double tap the power button to alternate between the 16 different colors. Pause in between switching colors, or you may accidentally power the saber off when double tapping too frequently.

  • To remove blade: With the hex key provided, remove the screws at the base of the blade (keep these screws in a safe place so you can put them back in when you are ready to reattach your blade). Gently pull the blade out of the hilt. Attach the red cap to prevent dust and other materials from getting inside of your blade. To reattach your blade, gently slide it back into the hilt and fasten the screws back into place. Make sure to tighten the screws efficiently; loose screws may cause damage to your saber when dueling or cause your blade to fly out when swung.

  • To make a double sided saber: Unscrew the bottom piece of your saber VERY carefully. When you take this piece off you are exposing the inner electronics, therefore it is pertinent that you do not disturb the wiring, otherwise you may damage your sabers ability to work properly. Once you have unscrewed the first saber, screw the coupler on to it (KEEP the circular mesh piece inside, do not remove it when you take the end off). Once the coupler has been screwed on to the first saber, you should then carefully screw the end off of the second saber and attach it to the coupler. Please be sure to screw the coupler on tightly to both ends so that it does not become loose during use. Stow the ends of your sabers in a safe place, if you lose them you will have no bottom to your saber when you uncouple the sabers! NOTE: when attaching the coupler, make sure the wires do not become twisted. If they become twisted they could disconnect.

  • Enable lock up effect: while dueling, hold down the power button for however long you please to enable the lockup effect.

  • To charge your saber: Your sabers lights will begin to dim and flicker when it needs to be charged. Plug the accompanying power cord into any USB charging device and plug the opposite end into the charging port on your saber. The power button will flash while the saber is charging. For a full charge, leave your saber plugged in for 3-4 hours. *Charging times may vary depending on power source.

  • To change sound fonts: while saber is off, hold power button down for three seconds. Illuminated ring will flash. While flashing, tap to cycle between sound fonts. To set the desired sound font, hold down on the power button for three seconds. The ring will no longer be illuminated. The next time you power on your saber, the changes will have taken effect. 

Tier 1:

  • Grey Facebook Icon
  • Grey Instagram Icon
  • Grey Twitter Icon
  • Grey YouTube Icon

© 2017 by Spartan Sabers, LLC